Driver API for NAND Flash Device Interface (Driver_NAND.h). More...

Content
	Status Error Codes
	Negative values indicate errors (NAND has specific codes in addition to common Status Error Codes).

	NAND Events
	The NAND driver generates call back events that are notified via the function ARM_NAND_SignalEvent.

	NAND Flags
	Specify Flag codes.

	NAND Control Codes
	Many parameters of the NAND driver are configured using the ARM_NAND_Control function.

	NAND ECC Codes
	Specify ECC codes.

	NAND Sequence Execution Codes
	Specify execution codes.

Data Structures
struct	ARM_NAND_STATUS
	NAND Status. More...

struct	ARM_DRIVER_NAND
	Access structure of the NAND Driver. More...

struct	ARM_NAND_CAPABILITIES
	NAND Driver Capabilities. More...

struct	ARM_NAND_ECC_INFO
	NAND ECC (Error Correction Code) Information. More...

Typedefs
typedef void(*	ARM_NAND_SignalEvent_t )(uint32_t dev_num, uint32_t event)
	Pointer to ARM_NAND_SignalEvent : Signal NAND Event. More...

Functions
ARM_DRIVER_VERSION	ARM_NAND_GetVersion (void)
	Get driver version. More...

ARM_NAND_CAPABILITIES	ARM_NAND_GetCapabilities (void)
	Get driver capabilities. More...

int32_t	ARM_NAND_Initialize (ARM_NAND_SignalEvent_t cb_event)
	Initialize the NAND Interface. More...

int32_t	ARM_NAND_Uninitialize (void)
	De-initialize the NAND Interface. More...

int32_t	ARM_NAND_PowerControl (ARM_POWER_STATE state)
	Control the NAND interface power. More...

int32_t	ARM_NAND_DevicePower (uint32_t voltage)
	Set device power supply voltage. More...

int32_t	ARM_NAND_WriteProtect (uint32_t dev_num, bool enable)
	Control WPn (Write Protect). More...

int32_t	ARM_NAND_ChipEnable (uint32_t dev_num, bool enable)
	Control CEn (Chip Enable). More...

int32_t	ARM_NAND_GetDeviceBusy (uint32_t dev_num)
	Get Device Busy pin state. More...

int32_t	ARM_NAND_SendCommand (uint32_t dev_num, uint8_t cmd)
	Send command to NAND device. More...

int32_t	ARM_NAND_SendAddress (uint32_t dev_num, uint8_t addr)
	Send address to NAND device. More...

int32_t	ARM_NAND_ReadData (uint32_t dev_num, void *data, uint32_t cnt, uint32_t mode)
	Read data from NAND device. More...

int32_t	ARM_NAND_WriteData (uint32_t dev_num, const void *data, uint32_t cnt, uint32_t mode)
	Write data to NAND device. More...

int32_t	ARM_NAND_ExecuteSequence (uint32_t dev_num, uint32_t code, uint32_t cmd, uint32_t addr_col, uint32_t addr_row, void data, uint32_t data_cnt, uint8_t status, uint32_t *count)
	Execute sequence of operations. More...

int32_t	ARM_NAND_AbortSequence (uint32_t dev_num)
	Abort sequence execution. More...

int32_t	ARM_NAND_Control (uint32_t dev_num, uint32_t control, uint32_t arg)
	Control NAND Interface. More...

ARM_NAND_STATUS	ARM_NAND_GetStatus (uint32_t dev_num)
	Get NAND status. More...

int32_t	ARM_NAND_InquireECC (int32_t index, ARM_NAND_ECC_INFO *info)
	Inquire about available ECC. More...

void	ARM_NAND_SignalEvent (uint32_t dev_num, uint32_t event)
	Signal NAND event. More...

Description

Driver API for NAND Flash Device Interface (Driver_NAND.h).

NAND devices are a type of non-volatile storage and do not require power to hold data. Wikipedia offers more information about the Flash Memories, including NAND.

Block Diagram

Simplified NAND Flash Schematic

NAND API

The following header files define the Application Programming Interface (API) for the NAND interface:

Driver_NAND.h : Driver API for NAND Flash Device Interface

The driver implementation is a typical part of the Device Family Pack (DFP) that supports the peripherals of the microcontroller family.

NAND Flash is organized in pages, grouped into blocks as the smallest erasable unit. The addressing of data is archieved by byte_address = block * block_size + page_in_block * page_size + offset_in_page. In terms of this NAND API blocks and pages are referrd to as row and the byte offset within the page as col. Thus one can calculate the byte_address = row * page_size + col. The parameters page_size and block_size are device specific and must be handled by the driver user appropriately.

Driver Functions

The driver functions are published in the access struct as explained in Common Driver Functions

ARM_DRIVER_NAND : access struct for NAND driver functions

Example Code:

#include "Driver_NAND.h"
 
/* ONFI commands */
#define ONFI_CMD_READ_1ST               0x00   ///< Read 1st Cycle
#define ONFI_CMD_PROGRAM_2ND            0x10   ///< Page Program 2nd Cycle
#define ONFI_CMD_READ_2ND               0x30   ///< Read 2nd Cycle
#define ONFI_CMD_PROGRAM_1ST            0x80   ///< Page Program 1st Cycle
#define ONFI_CMD_RESET                  0xFF   ///< Reset Command
 
/* NAND Signal Event callback function */
volatile uint32_t NAND_Events;
void NAND_SignalEventCallback (uint32_t dev_num, uint32_t event) {
  if (dev_num == 0) {
    NAND_Events |= event;
  }
  else {
    // ..
  }
}
 
/* NAND device Power ON */
void PowerOn (ARM_DRIVER_NAND *drv, uint32_t dev_num) {
  ARM_NAND_CAPABILITIES capabilities;
 
  // Query drivers capabilities
  capabilities = drv->GetCapabilities();
 
  // Initialize NAND device
  drv->Initialize (NAND_SignalEventCallback);
 
  // Power-on NAND driver
  drv->PowerControl (ARM_POWER_FULL);
 
  // Turn ON device power
  uint32_t volt = 0U;
 
  if (capabilities.vcc)      { volt |= ARM_NAND_POWER_VCC_3V3;  }
  if (capabilities.vcc_1v8)  { volt |= ARM_NAND_POWER_VCC_1V8;  }
  if (capabilities.vccq)     { volt |= ARM_NAND_POWER_VCCQ_3V3; }
  if (capabilities.vccq_1v8) { volt |= ARM_NAND_POWER_VCCQ_1V8; }
 
  if (volt != 0U) {  
    drv->DevicePower (volt);
  }
 
  // Setting bus mode
  drv->Control (0U, ARM_NAND_BUS_MODE, ARM_NAND_BUS_SDR);
 
  // Setting bus data width
  drv->Control (0U, ARM_NAND_BUS_DATA_WIDTH, ARM_NAND_BUS_DATA_WIDTH_8);
 
  // Enable chip manually if needed
  if (capabilities.ce_manual) {
    drv->ChipEnable (dev_num, true);
  }
 
  // Send ONFI Reset command */
  drv->SendCommand (dev_num, ONFI_CMD_RESET);
}
 
/* NAND device Power OFF */
void PowerOff (ARM_DRIVER_NAND *drv, uint32_t dev_num) {
  ARM_NAND_CAPABILITIES capabilities;
 
  // Query drivers capabilities
  capabilities = drv->GetCapabilities();
 
  // Disable chip manually if needed
  if (capabilities.ce_manual) {
    drv->ChipEnable (0U, false);
  }
 
  // Switch OFF gracefully
  uint32_t volt = 0U;
 
  if (capabilities.vcc)  { volt |= ARM_NAND_POWER_VCC_OFF;  }
  if (capabilities.vccq) { volt |= ARM_NAND_POWER_VCCQ_OFF; }
  if (volt) {
    drv->DevicePower (volt);
  }
  drv->PowerControl (ARM_POWER_OFF);
  drv->Uninitialize ();
}
 
/* Read NAND page. */
void ReadPage (ARM_DRIVER_NAND *drv, uint32_t row, uint8_t *data, uint32_t cnt) {
  uint32_t dev_num = 0;   // Device number
  uint32_t mode;
 
  // Send Read 1st command
  drv->SendCommand (dev_num, ONFI_CMD_READ_1ST);
 
  // Send address (column: 2 cycles, row: 3 cycles)
  drv->SendAddress (dev_num, 0x00);
  drv->SendAddress (dev_num, 0x00);
  drv->SendAddress (dev_num, (uint8_t)(row));
  drv->SendAddress (dev_num, (uint8_t)(row >>  8));
  drv->SendAddress (dev_num, (uint8_t)(row >> 16));
 
  // Send Read 2nd command
  drv->SendCommand (dev_num, ONFI_CMD_READ_2ND);
 
  // Wait until device ready
  while (drv->GetDeviceBusy(dev_num) == 1) { ; }
 
  // Use ECC algorithm number 2, ECC0 (ECC over main+spare)
  mode = ARM_NAND_ECC(2) | ARM_NAND_ECC0;
 
  // Transfer data from the NAND chip
  if (drv->ReadData (dev_num, data, cnt, mode | ARM_NAND_DRIVER_DONE_EVENT) != cnt) {
    // Wait until driver done event received
    while ((NAND_Events & ARM_NAND_DRIVER_DONE_EVENT) == 0) { ; }
    // Read page completed
 
    if ((NAND_Events & ARM_NAND_EVENT_ECC_ERROR) != 0) {
      // ECC correction failed
    }
  }
}
 
/* Write NAND page (ExecuteSequence interface). */
void WritePage_Seq (ARM_DRIVER_NAND *drv, uint32_t row, const uint8_t *data, uint32_t cnt) {
  uint32_t dev_num = 0;   // Device number
  uint32_t cmd;
  uint32_t code;
  uint32_t seq;
 
  // Prepare commands to send
  cmd = ONFI_CMD_PROGRAM_1ST | (ONFI_CMD_PROGRAM_2ND << 8);
 
  // Construct sequence code:
  // - Send command 1
  // - Send 2 cycles of column address and 3 cycles of row address
  // - Write data from memory to device
  // - Send command 2
  code = ARM_NAND_CODE_SEND_CMD1      |
         ARM_NAND_CODE_SEND_ADDR_COL1 |
         ARM_NAND_CODE_SEND_ADDR_COL2 |
         ARM_NAND_CODE_SEND_ADDR_ROW1 |
         ARM_NAND_CODE_SEND_ADDR_ROW2 |
         ARM_NAND_CODE_SEND_ADDR_ROW3 |
         ARM_NAND_CODE_WRITE_DATA     |
         ARM_NAND_CODE_SEND_CMD2      ;
 
  // - Use ECC algorithm number 2, ECC0 (ECC over main+spare)
  code |= ARM_NAND_ECC(2) | ARM_NAND_ECC0;
 
  // Number of iterations in a sequence
  seq = 1;
 
  drv->ExecuteSequence (dev_num,        // Device number
                        code,           // Sequence code
                        cmd,            // Command(s)
                        0,              // Column address
                        row,            // Row address
                        (void *)data,   // Data buffer
                        cnt,            // Number of data items (per iteration)
                        NULL,           // Device status will not be read
                        &seq);          // Number of iterations
 
  // Wait until done
  while (drv->GetStatus(dev_num).busy != 0) { ; }
 
  // Page write completed
}

Data Structure Documentation

struct ARM_NAND_STATUS

NAND Status.

Structure with information about the status of a NAND. The data fields encode flags for the driver.

Returned by:

ARM_NAND_GetStatus

Data Fields
uint32_t	busy: 1	Driver busy flag.
uint32_t	ecc_error: 1	ECC error detected (cleared on next Read/WriteData or ExecuteSequence)
uint32_t	reserved: 30

struct ARM_DRIVER_NAND

Access structure of the NAND Driver.

The functions of the NAND driver are accessed by function pointers exposed by this structure. Refer to Common Driver Functions for overview information.

Each instance of a NAND interface provides such an access structure. The instance is identified by a postfix number in the symbol name of the access structure, for example:

Driver_NAND0 is the name of the access struct of the first instance (no. 0).
Driver_NAND1 is the name of the access struct of the second instance (no. 1).

A middleware configuration setting allows connecting the middleware to a specific driver instance Driver_NANDn. The default is 0, which connects a middleware to the first instance of a driver.

Data Fields
ARM_DRIVER_VERSION(*	GetVersion )(void)
	Pointer to ARM_NAND_GetVersion : Get driver version. More...

ARM_NAND_CAPABILITIES(*	GetCapabilities )(void)
	Pointer to ARM_NAND_GetCapabilities : Get driver capabilities. More...

int32_t(*	Initialize )(ARM_NAND_SignalEvent_t cb_event)
	Pointer to ARM_NAND_Initialize : Initialize NAND Interface. More...

int32_t(*	Uninitialize )(void)
	Pointer to ARM_NAND_Uninitialize : De-initialize NAND Interface. More...

int32_t(*	PowerControl )(ARM_POWER_STATE state)
	Pointer to ARM_NAND_PowerControl : Control NAND Interface Power. More...

int32_t(*	DevicePower )(uint32_t voltage)
	Pointer to ARM_NAND_DevicePower : Set device power supply voltage. More...

int32_t(*	WriteProtect )(uint32_t dev_num, bool enable)
	Pointer to ARM_NAND_WriteProtect : Control WPn (Write Protect). More...

int32_t(*	ChipEnable )(uint32_t dev_num, bool enable)
	Pointer to ARM_NAND_ChipEnable : Control CEn (Chip Enable). More...

int32_t(*	GetDeviceBusy )(uint32_t dev_num)
	Pointer to ARM_NAND_GetDeviceBusy : Get Device Busy pin state. More...

int32_t(*	SendCommand )(uint32_t dev_num, uint8_t cmd)
	Pointer to ARM_NAND_SendCommand : Send command to NAND device. More...

int32_t(*	SendAddress )(uint32_t dev_num, uint8_t addr)
	Pointer to ARM_NAND_SendAddress : Send address to NAND device. More...

int32_t(*	ReadData )(uint32_t dev_num, void *data, uint32_t cnt, uint32_t mode)
	Pointer to ARM_NAND_ReadData : Read data from NAND device. More...

int32_t(*	WriteData )(uint32_t dev_num, const void *data, uint32_t cnt, uint32_t mode)
	Pointer to ARM_NAND_WriteData : Write data to NAND device. More...

int32_t(*	ExecuteSequence )(uint32_t dev_num, uint32_t code, uint32_t cmd, uint32_t addr_col, uint32_t addr_row, void data, uint32_t data_cnt, uint8_t status, uint32_t *count)
	Pointer to ARM_NAND_ExecuteSequence : Execute sequence of operations. More...

int32_t(*	AbortSequence )(uint32_t dev_num)
	Pointer to ARM_NAND_AbortSequence : Abort sequence execution. More...

int32_t(*	Control )(uint32_t dev_num, uint32_t control, uint32_t arg)
	Pointer to ARM_NAND_Control : Control NAND Interface. More...

ARM_NAND_STATUS(*	GetStatus )(uint32_t dev_num)
	Pointer to ARM_NAND_GetStatus : Get NAND status. More...

int32_t(*	InquireECC )(int32_t index, ARM_NAND_ECC_INFO *info)
	Pointer to ARM_NAND_InquireECC : Inquire about available ECC. More...

Field Documentation

ARM_DRIVER_VERSION(* GetVersion)(void)

Pointer to ARM_NAND_GetVersion : Get driver version.

ARM_NAND_CAPABILITIES(* GetCapabilities)(void)

Pointer to ARM_NAND_GetCapabilities : Get driver capabilities.

int32_t(* Initialize)(ARM_NAND_SignalEvent_t cb_event)

Pointer to ARM_NAND_Initialize : Initialize NAND Interface.

int32_t(* Uninitialize)(void)

Pointer to ARM_NAND_Uninitialize : De-initialize NAND Interface.

int32_t(* PowerControl)(ARM_POWER_STATE state)

Pointer to ARM_NAND_PowerControl : Control NAND Interface Power.

int32_t(* DevicePower)(uint32_t voltage)

Pointer to ARM_NAND_DevicePower : Set device power supply voltage.

int32_t(* WriteProtect)(uint32_t dev_num, bool enable)

Pointer to ARM_NAND_WriteProtect : Control WPn (Write Protect).

int32_t(* ChipEnable)(uint32_t dev_num, bool enable)

Pointer to ARM_NAND_ChipEnable : Control CEn (Chip Enable).

int32_t(* GetDeviceBusy)(uint32_t dev_num)

Pointer to ARM_NAND_GetDeviceBusy : Get Device Busy pin state.

int32_t(* SendCommand)(uint32_t dev_num, uint8_t cmd)

Pointer to ARM_NAND_SendCommand : Send command to NAND device.

int32_t(* SendAddress)(uint32_t dev_num, uint8_t addr)

Pointer to ARM_NAND_SendAddress : Send address to NAND device.

int32_t(* ReadData)(uint32_t dev_num, void *data, uint32_t cnt, uint32_t mode)

Pointer to ARM_NAND_ReadData : Read data from NAND device.

int32_t(* WriteData)(uint32_t dev_num, const void *data, uint32_t cnt, uint32_t mode)

Pointer to ARM_NAND_WriteData : Write data to NAND device.

int32_t(* ExecuteSequence)(uint32_t dev_num, uint32_t code, uint32_t cmd, uint32_t addr_col, uint32_t addr_row, void *data, uint32_t data_cnt, uint8_t *status, uint32_t *count)

Pointer to ARM_NAND_ExecuteSequence : Execute sequence of operations.

int32_t(* AbortSequence)(uint32_t dev_num)

Pointer to ARM_NAND_AbortSequence : Abort sequence execution.

int32_t(* Control)(uint32_t dev_num, uint32_t control, uint32_t arg)

Pointer to ARM_NAND_Control : Control NAND Interface.

ARM_NAND_STATUS(* GetStatus)(uint32_t dev_num)

Pointer to ARM_NAND_GetStatus : Get NAND status.

int32_t(* InquireECC)(int32_t index, ARM_NAND_ECC_INFO *info)

Pointer to ARM_NAND_InquireECC : Inquire about available ECC.

struct ARM_NAND_CAPABILITIES

NAND Driver Capabilities.

A NAND driver can be implemented with different capabilities. The data fields of this struct encode the capabilities implemented by this driver.

Returned by:

ARM_NAND_GetCapabilities

Data Fields
uint32_t	event_device_ready: 1	Signal Device Ready event (R/Bn rising edge)
uint32_t	reentrant_operation: 1	Supports re-entrant operation (SendCommand/Address, Read/WriteData)
uint32_t	sequence_operation: 1	Supports Sequence operation (ExecuteSequence, AbortSequence)
uint32_t	vcc: 1	Supports VCC Power Supply Control.
uint32_t	vcc_1v8: 1	Supports 1.8 VCC Power Supply.
uint32_t	vccq: 1	Supports VCCQ I/O Power Supply Control.
uint32_t	vccq_1v8: 1	Supports 1.8 VCCQ I/O Power Supply.
uint32_t	vpp: 1	Supports VPP High Voltage Power Supply Control.
uint32_t	wp: 1	Supports WPn (Write Protect) Control.
uint32_t	ce_lines: 4	Number of CEn (Chip Enable) lines: ce_lines + 1.
uint32_t	ce_manual: 1	Supports manual CEn (Chip Enable) Control.
uint32_t	rb_monitor: 1	Supports R/Bn (Ready/Busy) Monitoring.
uint32_t	data_width_16: 1	Supports 16-bit data.
uint32_t	ddr: 1	Supports NV-DDR Data Interface (ONFI)
uint32_t	ddr2: 1	Supports NV-DDR2 Data Interface (ONFI)
uint32_t	sdr_timing_mode: 3	Fastest (highest) SDR Timing Mode supported (ONFI)
uint32_t	ddr_timing_mode: 3	Fastest (highest) NV_DDR Timing Mode supported (ONFI)
uint32_t	ddr2_timing_mode: 3	Fastest (highest) NV_DDR2 Timing Mode supported (ONFI)
uint32_t	driver_strength_18: 1	Supports Driver Strength 2.0x = 18 Ohms.
uint32_t	driver_strength_25: 1	Supports Driver Strength 1.4x = 25 Ohms.
uint32_t	driver_strength_50: 1	Supports Driver Strength 0.7x = 50 Ohms.
uint32_t	reserved: 2	Reserved (must be zero)

struct ARM_NAND_ECC_INFO

NAND ECC (Error Correction Code) Information.

Stores the characteristics of a ECC (Error Correction Code) algorithm and provides the information about necessary application data handling in order to protect stored data from NAND bit errors.

ECC algorithms applied on NAND memory typically operate on NAND device page level which is virtually divided to multiple main and spare areas. Data from main and spare area is taken into account when generating ECC data which is also stored into spare area. ECC codeword defines how much data will be protected and how much ECC data will be generated.

To describe how application data must be organized, ECC information structure specifies protection type which defines the protected part of data. As main and spare are of different size, two different algorithms could be provided, we can describe them as ECC0 and ECC1. Type can then have the following values:

Type	Description
0	ECC algorithm not used
1	ECC0 algorithm protects main data
2	ECC0 algorithm protects main and spare data
3	ECC0 algorithm protects main and ECC1 algorithm protects spare data

Virtual page division is described with page layout (page_layout), number of pages (page_count) and virtual page size (page_size or virtual_page_size). Virtual page size used by ECC algorithm can be defined by either page_size or virtual_page_size, depending on the page_size values:

Value	Main + Spare size
0	512 + 16
1	1024 + 32
2	2048 + 64
3	4096 + 128
4	8192 + 256
8	512 + 28
9	1024 + 56
10	2048 + 112
11	4096 + 224
12	8192 + 448
15	Not used, use virtual_page_size

Structure member virtual_page_size is an array of two 16-bit values. First field of array (i.e. virtual_page_size[0]) contains main area size while second (i.e. virtual_page_size[1]) contains spare area size. Number of virtual pages N is defined with page_count and must be calculated as N = 2 ^ page_count.

Page layout defines main and spare ordering and two different page layouts are possible. First ordering assumes that spare area follows after every main area, while in second case all main areas build one contiguous region followed by contiguous region of spare areas. This is defined by member page_layout:

Layout	Description
0	Single spare follows after single main: Main0,Spare0 ... MainN-1,SpareN-1
1	Contiguous spare follows after contiguous main: Main0 ... MainN-1,Spare0 ... SpareN-1

ECC codeword size defines the size of data that is protected by ECC algorithm and is different for main and spare area. All structure members that define the codeword are therefore arrays of two 16-bit values. Codeword offset defines where ECC protected data starts in main (codeword_offset[0]) or spare (codeword_offset[1]) area, codeword size (codeword_size) defines the number of data that is protected i.e. data over which ECC is calculated and codeword gap (codeword_gap) defines the space between two consecutive codeword regions.

Generated ECC data is stored into spare area and is described similar as codeword, with offset from start of spare area (ecc_offset), size of generated data (ecc_size) and gap (ecc_gap) between two consecutive ECC data regions.

Number of bits that ECC algorithm can correct per codeword is defined with correctable_bits.

Parameter for:

ARM_NAND_InquireECC

Data Fields
uint32_t	type: 2	Type: 1=ECC0 over Main, 2=ECC0 over Main+Spare, 3=ECC0 over Main and ECC1 over Spare.
uint32_t	page_layout: 1	Page layout: 0=\|Main0\|Spare0\|...\|MainN-1\|SpareN-1\|, 1=\|Main0\|...\|MainN-1\|Spare0\|...\|SpareN-1\|.
uint32_t	page_count: 3	Number of virtual pages: N = 2 ^ page_count.
uint32_t	page_size: 4	Virtual Page size (Main+Spare): 0=512+16, 1=1k+32, 2=2k+64, 3=4k+128, 4=8k+256, 8=512+28, 9=1k+56, 10=2k+112, 11=4k+224, 12=8k+448, 15=Not used (extended description)
uint32_t	reserved: 14	Reserved (must be zero)
uint32_t	correctable_bits: 8	Number of correctable bits (based on 512 byte codeword size)
uint16_t	codeword_size[2]	Number of bytes over which ECC is calculated.
uint16_t	ecc_size[2]	ECC size in bytes (rounded up)
uint16_t	ecc_offset[2]	ECC offset in bytes (where ECC starts in Spare)
uint16_t	virtual_page_size[2]	Virtual Page size in bytes (Main/Spare)
uint16_t	codeword_offset[2]	Codeword offset in bytes (where ECC protected data starts in Main/Spare)
uint16_t	codeword_gap[2]	Codeword gap in bytes till next protected data.
uint16_t	ecc_gap[2]	ECC gap in bytes till next generated ECC.

Typedef Documentation

ARM_NAND_SignalEvent_t

Pointer to ARM_NAND_SignalEvent : Signal NAND Event.

Provides the typedef for the callback function ARM_NAND_SignalEvent.

Parameter for:

ARM_NAND_Initialize

Function Documentation

ARM_DRIVER_VERSION ARM_NAND_GetVersion ( void )

Get driver version.

Returns: ARM_DRIVER_VERSION

The function ARM_NAND_GetVersion returns version information of the driver implementation in ARM_DRIVER_VERSION

API version is the version of the CMSIS-Driver specification used to implement this driver.
Driver version is source code version of the actual driver implementation.

Example:

extern ARM_DRIVER_NAND Driver_NAND0;
ARM_DRIVER_NAND *drv_info;
 
void setup_nand (void)  {
  ARM_DRIVER_VERSION  version;
 
  drv_info = &Driver_NAND0;  
  version = drv_info->GetVersion ();
  if (version.api < 0x10A)   {      // requires at minimum API version 1.10 or higher
    // error handling
    return;
  }
}

ARM_NAND_CAPABILITIES ARM_NAND_GetCapabilities ( void )

Get driver capabilities.

Returns: ARM_NAND_CAPABILITIES

The function ARM_NAND_GetCapabilities retrieves information about capabilities in this driver implementation. The data fields of the structure ARM_NAND_CAPABILITIES encode various capabilities, for example if a hardware is able to create signal events using the ARM_NAND_SignalEvent callback function.

Example:

extern ARM_DRIVER_NAND Driver_NAND0;
ARM_DRIVER_NAND *drv_info;
  
void read_capabilities (void)  {
  ARM_NAND_CAPABILITIES drv_capabilities;
 
  drv_info = &Driver_NAND0;  
  drv_capabilities = drv_info->GetCapabilities ();
  // interrogate capabilities
 
}

int32_t ARM_NAND_Initialize ( ARM_NAND_SignalEvent_t cb_event )

Initialize the NAND Interface.

Parameters

[in] cb_event Pointer to ARM_NAND_SignalEvent

Returns: Status Error Codes

The function ARM_NAND_Initialize initializes the NAND interface. It is called when the middleware component starts operation.

The function performs the following operations:

Initializes the resources needed for the NAND interface.
Registers the ARM_NAND_SignalEvent callback function.

The parameter cb_event is a pointer to the ARM_NAND_SignalEvent callback function; use a NULL pointer when no callback signals are required.

Example:

see NAND Interface - Driver Functions

int32_t ARM_NAND_Uninitialize ( void )

De-initialize the NAND Interface.

Returns: Status Error Codes

The function ARM_NAND_Uninitialize de-initializes the resources of NAND interface.

It is called when the middleware component stops operation and releases the software resources used by the interface.

int32_t ARM_NAND_PowerControl ( ARM_POWER_STATE state )

Control the NAND interface power.

Parameters

[in] state Power state

Returns: Status Error Codes

The function ARM_NAND_PowerControl controls the power modes of the NAND interface.

The parameter state sets the operation and can have the following values:

ARM_POWER_FULL : set-up peripheral for data transfers, enable interrupts (NVIC) and optionally DMA. Can be called multiple times. If the peripheral is already in this mode the function performs no operation and returns with ARM_DRIVER_OK.
ARM_POWER_LOW : may use power saving. Returns ARM_DRIVER_ERROR_UNSUPPORTED when not implemented.
ARM_POWER_OFF : terminates any pending data transfers, disables peripheral, disables related interrupts and DMA.

Refer to Function Call Sequence for more information.

int32_t ARM_NAND_DevicePower ( uint32_t voltage )

Set device power supply voltage.

Parameters

[in] voltage NAND Device supply voltage

Returns: Status Error Codes

The function ARM_NAND_DevicePower controls the power supply of the NAND device.

The parameter voltage sets the device supply voltage as defined in the table.

AMR_NAND_POWER_xxx_xxx specifies power settings.

Device Power Bits	Description
ARM_NAND_POWER_VCC_OFF	Set VCC Power off
ARM_NAND_POWER_VCC_3V3	Set VCC = 3.3V
ARM_NAND_POWER_VCC_1V8	Set VCC = 1.8V
ARM_NAND_POWER_VCCQ_OFF	Set VCCQ I/O Power off
ARM_NAND_POWER_VCCQ_3V3	Set VCCQ = 3.3V
ARM_NAND_POWER_VCCQ_1V8	Set VCCQ = 1.8V
ARM_NAND_POWER_VPP_OFF	Set VPP off
ARM_NAND_POWER_VPP_ON	Set VPP on

int32_t ARM_NAND_WriteProtect	(	uint32_t	dev_num,
		bool	enable
	)

Control WPn (Write Protect).

Parameters

[in]	dev_num	Device number
[in]	enable	false Write Protect off true Write Protect on

Returns: Status Error Codes

The function ARM_NAND_WriteProtect controls the Write Protect (WPn) pin of a NAND device.

The parameter dev_num is the device number.
The parameter enable specifies whether to enable or disable write protection.

int32_t ARM_NAND_ChipEnable	(	uint32_t	dev_num,
		bool	enable
	)

Control CEn (Chip Enable).

Parameters

[in]	dev_num	Device number
[in]	enable	false Chip Enable off true Chip Enable on

Returns: Status Error Codes

The function ARM_NAND_ChipEnable control the Chip Enable (CEn) pin of a NAND device.

The parameter dev_num is the device number.
The parameter enable specifies whether to enable or disable the device.

This function is optional and supported only when the data field ce_manual = 1 in the structure ARM_NAND_CAPABILITIES. Otherwise, the Chip Enable (CEn) signal is controlled automatically by SendCommand/Address, Read/WriteData and ExecuteSequence (for example when the NAND device is connected to a memory bus).

int32_t ARM_NAND_GetDeviceBusy ( uint32_t dev_num )

Get Device Busy pin state.

Parameters

[in] dev_num Device number

Returns: 1=busy, 0=not busy, or error

The function ARM_NAND_GetDeviceBusy returns the status of the Device Busy pin: [1=busy; 0=not busy or error].

The parameter dev_num is the device number.

int32_t ARM_NAND_SendCommand	(	uint32_t	dev_num,
		uint8_t	cmd
	)

Send command to NAND device.

Parameters

[in]	dev_num	Device number
[in]	cmd	Command

Returns: Status Error Codes

The function ARM_NAND_SendCommand sends a command to the NAND device.

The parameter dev_num is the device number.
The parameter cmd is the command sent to the NAND device.

int32_t ARM_NAND_SendAddress	(	uint32_t	dev_num,
		uint8_t	addr
	)

Send address to NAND device.

Parameters

[in]	dev_num	Device number
[in]	addr	Address

Returns: Status Error Codes

Send an address to the NAND device. The parameter dev_num is the device number. The parameter addr is the address.

int32_t ARM_NAND_ReadData	(	uint32_t	dev_num,
		void *	data,
		uint32_t	cnt,
		uint32_t	mode
	)

Read data from NAND device.

Parameters

[in]	dev_num	Device number
[out]	data	Pointer to buffer for data to read from NAND device
[in]	cnt	Number of data items to read
[in]	mode	Operation mode

Returns: number of data items read or Status Error Codes

The function ARM_NAND_ReadData reads data from a NAND device.

The parameter dev_num is the device number.
The parameter data is a pointer to the buffer that stores the data read from a NAND device.
The parameter cnt is the number of data items to read.
The parameter mode defines the operation mode as listed in the table below.

Read Data Mode	Description
ARM_NAND_ECC(n)	Select ECC
ARM_NAND_ECC0	Use ECC0 of selected ECC
ARM_NAND_ECC1	Use ECC1 of selected ECC
ARM_NAND_DRIVER_DONE_EVENT	Generate ARM_NAND_EVENT_DRIVER_DONE

The data item size is defined by the data type, which depends on the configured data bus width.

Data type is:

uint8_t for 8-bit data bus
uint16_t for 16-bit data bus

The function executes in the following ways:

When the operation is blocking (typical for devices connected to memory bus when not using DMA), then the function returns after all data is read and returns the number of data items read.
When the operation is non-blocking (typical for NAND controllers), then the function only starts the operation and returns with zero number of data items read. After the operation is completed, the ARM_NAND_EVENT_DRIVER_DONE event is generated (if enabled by ARM_NAND_DRIVER_DONE_EVENT). Progress of the operation can also be monitored by calling the ARM_NAND_GetStatus function and checking the busy data field. Operation is automatically aborted if ECC is used and ECC correction fails, which generates the ARM_NAND_EVENT_ECC_ERROR event (together with ARM_NAND_DRIVER_DONE_EVENT if enabled).

int32_t ARM_NAND_WriteData	(	uint32_t	dev_num,
		const void *	data,
		uint32_t	cnt,
		uint32_t	mode
	)

Write data to NAND device.

Parameters

[in]	dev_num	Device number
[out]	data	Pointer to buffer with data to write to NAND device
[in]	cnt	Number of data items to write
[in]	mode	Operation mode

Returns: number of data items written or Status Error Codes

The function ARM_NAND_WriteData writes data to a NAND device.

The parameter dev_num is the device number.
The parameter data is a pointer to the buffer with data to write.
The parameter cnt is the number of data items to write.
The parameter mode defines the operation mode as listed in the table below.

Write Data Mode	Description
ARM_NAND_ECC(n)	Select ECC
ARM_NAND_ECC0	Use ECC0 of selected ECC
ARM_NAND_ECC1	Use ECC1 of selected ECC
ARM_NAND_DRIVER_DONE_EVENT	Generate ARM_NAND_EVENT_DRIVER_DONE

The data item size is defined by the data type, which depends on the configured data bus width.

Data type is:

uint8_t for 8-bit data bus
uint16_t for 16-bit data bus

The function executes in the following ways:

When the operation is blocking (typical for devices connected to memory bus when not using DMA), then the function returns after all data is written and returns the number of data items written.
When the operation is non-blocking (typical for NAND controllers), then the function only starts the operation and returns with zero number of data items written. After the operation is completed, the ARM_NAND_EVENT_DRIVER_DONE event is generated (if enabled by ARM_NAND_DRIVER_DONE_EVENT). Progress of the operation can also be monitored by calling the ARM_NAND_GetStatus function and checking the busy data field. Operation is automatically aborted if ECC is used and ECC generation fails, which generates the ARM_NAND_EVENT_ECC_ERROR event (together with ARM_NAND_DRIVER_DONE_EVENT if enabled).

int32_t ARM_NAND_ExecuteSequence	(	uint32_t	dev_num,
		uint32_t	code,
		uint32_t	cmd,
		uint32_t	addr_col,
		uint32_t	addr_row,
		void *	data,
		uint32_t	data_cnt,
		uint8_t *	status,
		uint32_t *	count
	)

Execute sequence of operations.

Parameters

[in]	dev_num	Device number
[in]	code	Sequence code
[in]	cmd	Command(s)
[in]	addr_col	Column address
[in]	addr_row	Row address
[in,out]	data	Pointer to data to be written or read
[in]	data_cnt	Number of data items in one iteration
[out]	status	Pointer to status read
[in,out]	count	Number of iterations

Returns: Status Error Codes

The function ARM_NAND_ExecuteSequence executes a sequence of operations for a NAND device.

The parameter dev_num is the device number.
The parameter code is the sequence encoding as defined in the table Sequence execution Code.
The parameter cmd is the command or a series of commands.
The parameter addr_col is the column address.
The parameter addr_row is the row address.
The parameter data is a pointer to the buffer that stores the data to or loads the data from.
The parameter data_cnt is the number of data items to read or write in one iteration.
The parameter status is a pointer to the buffer that stores the status read.
The parameter count is a pointer to the number of iterations.
ARM_NAND_CODE_xxx specifies sequence execution codes.

Sequence Execution Code	Description
ARM_NAND_CODE_SEND_CMD1	Send Command 1 (cmd[7..0])
ARM_NAND_CODE_SEND_ADDR_COL1	Send Column Address 1 (addr_col[7..0])
ARM_NAND_CODE_SEND_ADDR_COL2	Send Column Address 2 (addr_col[15..8])
ARM_NAND_CODE_SEND_ADDR_ROW1	Send Row Address 1 (addr_row[7..0])
ARM_NAND_CODE_SEND_ADDR_ROW2	Send Row Address 2 (addr_row[15..8])
ARM_NAND_CODE_SEND_ADDR_ROW3	Send Row Address 3 (addr_row[23..16])
ARM_NAND_CODE_INC_ADDR_ROW	Auto-increment Row Address
ARM_NAND_CODE_WRITE_DATA	Write Data
ARM_NAND_CODE_SEND_CMD2	Send Command 2 (cmd[15..8])
ARM_NAND_CODE_WAIT_BUSY	Wait while R/Bn busy
ARM_NAND_CODE_READ_DATA	Read Data
ARM_NAND_CODE_SEND_CMD3	Send Command 3 (cmd[23..16])
ARM_NAND_CODE_READ_STATUS	Read Status byte and check FAIL bit (bit 0)
ARM_NAND_ECC(n)	Select ECC
ARM_NAND_ECC0	Use ECC0 of selected ECC
ARM_NAND_ECC1	Use ECC1 of selected ECC
ARM_NAND_DRIVER_DONE_EVENT	Generate ARM_NAND_EVENT_DRIVER_DONE

The data item size is defined by the data type, which depends on the configured data bus width.

Data type is:

uint8_t for 8-bit data bus
uint16_t for 16-bit data bus

The function is non-blocking and returns as soon as the driver has started executing the specified sequence. When the operation is completed, the ARM_NAND_EVENT_DRIVER_DONE event is generated (if enabled by ARM_NAND_DRIVER_DONE_EVENT). Progress of the operation can also be monitored by calling the ARM_NAND_GetStatus function and checking the busy data field.

Driver executes the number of specified iterations where in each iteration items specified by ARM_NAND_CODE_xxx are executed in the order as listed in the table Sequence execution Code. The parameter count is holding the current number of iterations left.

Execution is automatically aborted and ARM_NAND_EVENT_DRIVER_DONE event is generated (if enabled by ARM_NAND_DRIVER_DONE_EVENT):

if Read Status is enabled and the FAIL bit (bit 0) is set
if ECC is used and ECC fails (also sets ARM_NAND_EVENT_ECC_ERROR event)

Note: ARM_NAND_CODE_WAIT_BUSY can only be specified if the Device Ready event can be generated (reported by event_device_ready in ARM_NAND_CAPABILITIES). The event ARM_NAND_EVENT_DEVICE_READY is not generated during sequence execution but rather used internally by the driver.

int32_t ARM_NAND_AbortSequence ( uint32_t dev_num )

Abort sequence execution.

Parameters

[in] dev_num Device number

Returns: Status Error Codes

The function ARM_NAND_AbortSequence aborts execution of the current sequence for a NAND device.

The parameter dev_num is the device number.

int32_t ARM_NAND_Control	(	uint32_t	dev_num,
		uint32_t	control,
		uint32_t	arg
	)

Control NAND Interface.

Parameters

[in]	dev_num	Device number
[in]	control	Operation
[in]	arg	Argument of operation

Returns: Status Error Codes

The function ARM_NAND_Control controls the NAND interface and executes operations.

The parameter dev_num is the device number.
The parameter control specifies the operation.
The parameter arg provides (depending on the control) additional information or sets values.

The table lists the operations for the parameter control.

Parameter control	Operation
ARM_NAND_BUS_MODE	Set the bus mode. The parameter arg sets the Bus Mode.
ARM_NAND_BUS_DATA_WIDTH	Set the data bus width. The parameter arg sets the Bus Data Width.
ARM_NAND_DRIVER_STRENGTH	Set the driver strength. The parameter arg sets the Driver Strength.
ARM_NAND_DRIVER_READY_EVENT	Control generation of callback event ARM_NAND_EVENT_DRIVER_READY. Enable: arg = 1. Disable: arg = 0.
ARM_NAND_DEVICE_READY_EVENT	Control generation of callback event ARM_NAND_EVENT_DEVICE_READY; Enable: arg = 1. Disable: arg = 0.

See Also

ARM_NAND_GetCapabilities returns information about supported operations, which are stored in the structure ARM_NAND_CAPABILITIES.
ARM_NAND_SignalEvent provides information about the callback events ARM_NAND_EVENT_DRIVER_READY and ARM_NAND_EVENT_DEVICE_READY

The table lists values for the parameter arg used with the control operation ARM_NAND_BUS_MODE, ARM_NAND_BUS_DATA_WIDTH, and ARM_NAND_DRIVER_STRENGTH. Values from different categories can be ORed.

Parameter arg for control = ARM_NAND_BUS_MODE	Bit	Category	Description	Supported when ARM_NAND_CAPABILITIES
ARM_NAND_BUS_TIMING_MODE_0 (default)	0..3	Bus Timing Mode	0	The maximum timing mode that can be applied to a specific Bus Data Interface is stored in the data fields: sdr_timing_mode - for SDR ddr_timing_mode - for NV-DDR ddr2_timing_mode - for NV_DDR2
ARM_NAND_BUS_TIMING_MODE_1			1
ARM_NAND_BUS_TIMING_MODE_2			2
ARM_NAND_BUS_TIMING_MODE_3			3
ARM_NAND_BUS_TIMING_MODE_4			4 (SDR EDO capable)
ARM_NAND_BUS_TIMING_MODE_5			5 (SDR EDO capable)
ARM_NAND_BUS_TIMING_MODE_6			6 (NV-DDR2 only)
ARM_NAND_BUS_TIMING_MODE_7			7 (NV-DDR2 only)
ARM_NAND_BUS_SDR (default)	4..7	Bus Data Interface	SDR (Single Data Rate) - Traditional interface	always supported
ARM_NAND_BUS_DDR			NV-DDR (Double Data Rate)	data field ddr = 1
ARM_NAND_BUS_DDR2			NV-DDR2 (Double Data Rate)	data field ddr2 = 1
ARM_NAND_BUS_DDR2_DO_WCYC_0 (default)	8..11	Data Output Warm-up	Set the DDR2 Data Output Warm-up to 0 cycles	Data Output Warm-up cycles are dummy cycles for interface calibration with no incremental data transfer and apply to NV-DDR2 of the Bus Data Interface.
ARM_NAND_BUS_DDR2_DO_WCYC_1			Set the DDR2 Data Output Warm-up to 1 cycles
ARM_NAND_BUS_DDR2_DO_WCYC_2			Set the DDR2 Data Output Warm-up to 2 cycles
ARM_NAND_BUS_DDR2_DO_WCYC_4			Set the DDR2 Data Output Warm-up to 4 cycles
ARM_NAND_BUS_DDR2_DI_WCYC_0 (default)	12..15	Data Input Warm-up	Set the DDR2 Data Input Warm-up to 0 cycles	Data Input Warm-up cycles are dummy cycles for interface calibration with no incremental data transfer and apply to NV-DDR2 of the Bus Data Interface.
ARM_NAND_BUS_DDR2_DI_WCYC_1			Set the DDR2 Data Input Warm-up to 1 cycles
ARM_NAND_BUS_DDR2_DI_WCYC_2			Set the DDR2 Data Input Warm-up to 2 cycles
ARM_NAND_BUS_DDR2_DI_WCYC_4			Set the DDR2 Data Input Warm-up to 4 cycles
ARM_NAND_BUS_DDR2_VEN	16	Miscellaneous	Set the DDR2 Enable external VREFQ as reference
ARM_NAND_BUS_DDR2_CMPD	17		Set the DDR2 Enable complementary DQS (DQS_c) signal
ARM_NAND_BUS_DDR2_CMPR	18		Set the DDR2 Enable complementary RE_n (RE_c) signal
Parameter arg for control = ARM_NAND_BUS_DATA_WIDTH	Bit	Category	Description	Supported when ARM_NAND_CAPABILITIES
ARM_NAND_BUS_DATA_WIDTH_8 (default)	0..1	Bus Data Width	Set to 8 bit	always supported
ARM_NAND_BUS_DATA_WIDTH_16	0..1	Bus Data Width	Set to 16 bit	data field data_width_16 = 1
Parameter arg for control = ARM_NAND_DRIVER_STRENGTH	Bit	Category	Description	Supported when ARM_NAND_CAPABILITIES
ARM_NAND_DRIVER_STRENGTH_18	0..3	Driver Strength	Set the Driver Strength 2.0x = 18 Ohms	data field driver_strength_18 = 1
ARM_NAND_DRIVER_STRENGTH_25			Set the Driver Strength 1.4x = 25 Ohms	data field driver_strength_25 = 1
ARM_NAND_DRIVER_STRENGTH_35 (default)			Set the Driver Strength 1.0x = 35 Ohms	always supported
ARM_NAND_DRIVER_STRENGTH_50			Set the Driver Strength 0.7x = 50 Ohms	data field driver_strength_50 = 1

Example

extern ARM_DRIVER_NAND Driver_NAND0;
 
status = Driver_NAND0.Control (0, ARM_NAND_BUS_MODE, ARM_NAND_BUS_TIMING_MODE_5 | 
                                                     ARM_NAND_BUS_DDR2          | 
                                                     ARM_NAND_BUS_DDR2_VEN);
                                                                                            
status = Driver_NAND0.Control (0, ARM_NAND_BUS_DATA_WIDTH,  ARM_NAND_BUS_DATA_WIDTH_16); 
 
status = Driver_NAND0.Control (0, ARM_NAND_DRIVER_STRENGTH, ARM_NAND_DRIVER_STRENGTH_50);

ARM_NAND_STATUS ARM_NAND_GetStatus ( uint32_t dev_num )

Get NAND status.

Parameters

[in] dev_num Device number

Returns: NAND status ARM_NAND_STATUS

The function ARM_NAND_GetStatus returns the current NAND device status.

The parameter dev_num is the device number.

int32_t ARM_NAND_InquireECC	(	int32_t	index,
		ARM_NAND_ECC_INFO *	info
	)

Inquire about available ECC.

Parameters

[in]	index	Inquire ECC index
[out]	info	Pointer to ECC information ARM_NAND_ECC_INFO retrieved

Returns: Status Error Codes

The function ARM_NAND_InquireECC reads error correction code information.

The parameter index is the ECC index and is used to retrieve different ECC configurations.
The parameter info is a pointer of type ARM_NAND_ECC_INFO. The data fields store the information.

When multiple different ECC configurations exist, ARM_NAND_ECC_INFO structure exists for each configuration. Parameter index denotes which configuration will be retrieved. Value of index should start with zero to retrieve first ECC configuration and should be incremented in order to retrieve next ECC configuration. When index is out of range function ARM_NAND_InquireECC returns with error.

Parameter index is used by ARM_NAND_ECC(n) in ARM_NAND_ReadData, ARM_NAND_WriteData and ARM_NAND_ExecuteSequence to select suitable ECC configuration.

Example

extern ARM_DRIVER_NAND Driver_NAND0; 
ARM_NAND_ECC_INFO ecc;
int32_t idx;
 
idx = 0;
while (Driver_NAND0.InquireECC (idx, &ecc) == ARM_DRIVER_OK) {
  // Examine retrieved ECC configuration
  if (ecc.type == 2) {
    // Algorithm ECC0 protects Main+Spare
  }
  // ..
  idx++;
}

void ARM_NAND_SignalEvent	(	uint32_t	dev_num,
		uint32_t	event
	)

Signal NAND event.

Parameters

[in]	dev_num	Device number
[in]	event	Event notification mask

Returns: none

The function ARM_NAND_SignalEvent is a callback function registered by the function ARM_NAND_Initialize.

The parameter dev_num is the device number.
The parameter event indicates one or more events that occurred during driver operation. Each event is encoded in a separate bit and therefore it is possible to signal multiple events within the same call.

Not every event is necessarily generated by the driver. This depends on the implemented capabilities stored in the data fields of the structure ARM_NAND_CAPABILITIES, which can be retrieved with the function ARM_NAND_GetCapabilities.

The following events can be generated:

Parameter event	Bit	Description
ARM_NAND_EVENT_DEVICE_READY	0	Occurs when rising edge is detected on R/Bn (Ready/Busy) pin indicating that the device is ready.
ARM_NAND_EVENT_DRIVER_READY	1	Occurs to indicate that commands can be executed (after previously being busy and not able to start the requested operation).
ARM_NAND_EVENT_DRIVER_DONE	2	Occurs after an operation completes. An operation was successfully started before with ARM_NAND_ReadData, ARM_NAND_WriteData, ARM_NAND_ExecuteSequence.
ARM_NAND_EVENT_ECC_ERROR	3	Occurs when ECC generation failed or ECC correction failed. An operation was successfully started before with ARM_NAND_ReadData, ARM_NAND_WriteData, ARM_NAND_ExecuteSequence.

The event ARM_NAND_EVENT_DEVICE_READY occurs after complete execution of commands (initiated with the functions ARM_NAND_SendCommand, ARM_NAND_SendAddress, ARM_NAND_ReadData, ARM_NAND_WriteData, ARM_NAND_ExecuteSequence). It is useful to indicate completion of complex operations (such as erase). The event is only generated when ARM_NAND_GetCapabilities returns data field event_device_ready = 1 and was enabled by calling ARM_NAND_Control (ARM_NAND_DEVICE_READY_EVENT, 1). If the event is not available, poll the busy data field using the function ARM_NAND_GetStatus.

The event ARM_NAND_EVENT_DRIVER_READY occurs when previously a function (ARM_NAND_SendCommand, ARM_NAND_SendAddress, ARM_NAND_ReadData, ARM_NAND_WriteData, ARM_NAND_ExecuteSequence) returned with ARM_DRIVER_ERROR_BUSY. It is useful when functions are called simultaneously from independent threads (for example to control multiple devices) and the threads have no knowledge about each other (driver rejects reentrant calls with return of ARM_DRIVER_ERROR_BUSY). dev_num indicates the device that returned previously busy.

Content

Data Structures

Typedefs

Functions

Description

Data Structure Documentation

Data Fields

Field Documentation

Typedef Documentation

Function Documentation